The "U" Adjustable Width Tray Slide Bracket Attaching System, model 32798, is lapboard mounting hardware designed to secure trays to wheelchairs. These brackets enable a tray (not included) to slide on to the armrests from the front and the configuration of the bracket enables it to be attached to the underside the of the tray and wrap around standard wheelchair armrest pads and attached to the underside of the armrest (mounting hardware is not included). These brackets can be mounted inside or
The "Z" Tray Slide Bracket Attaching System, model 32799, is lapboard mounting hardware designed to secure trays to wheelchairs. These brackets enable a tray (not included) to slide on to the armrests from the front. and the configuration of the bracket enables it to be attached to the underside of standard wheelchair armrest pads and the underside of the tray (mounting hardware is not included). A hook-and-loop strap attaching system (not included) may be used in conjunction with these brackets
The 1.5-inch Slide Bracket, model AB-1530, and the 1.5-inch ABS Spacer Plate, model AB-1815, are mounting hardware components designed for anchoring removable postural supports to solid seat and back panels. The Slide Bracket includes an F44-0476 Knob. The Spacer Plate is used to protect upholstery and ease insertion and removal of the bracket.
The 3-inch 90-degree Bracket, model LB-3030, and the 6-inch 90-degree Bracket, model LB-6060, are stainless steel brackets designed for constructing one-piece seating systems, attaching seats and backs together, or mounting lateral hip guides. The brackets have slotted holes for assembly into T-nuts after upholstery.
The Abductor Flip Down Kit, model 31467, is seating hardware general designed to allow abductors and lateral pads to swing away during wheelchair transfers. Designed to be used with the manufacturer's Abductor Pads or Lateral Pads (see separate entries), this kit includes one four-inch coated steel tapered L-bracket, one 2.75-inch coated steel slotted L-bracket, one 2.75-inch coated steel extrender, one anodized aluminum hinge, and mounting hardware. COLOR: Black.
The Adjustable Brackets are wheelchair seating hardware used in many areas such as wheelchair seat construction and wheelchair seat positioning with seat hooks. Made of stainless steel, both ends are rounded. One end is punched with two 17/64 inch x 5/8 inch slots and the other with a selected number of ##10 through holes. They are deburred for a smooth finish. Brackets are available with one, three, five, seven, or nine holes. COLOR: Available in black and stainless steel.
Adjustable Brackets are multi-hole brackets used in conjunction with seat hooks to enable a variety of seat positioning in wheelchairs. They are made of 11 gauge stainless steel with a 35 degree angle and available with 2, 3 4, 6, or 8 holes. Also available is an 8 hole, 2 inch extra long model. COLOR: Black.
The Adjustable Height Channel Bracket Attaching System is lapboard mounting hardware designed to secure trays to wheelchairs. These heavy-duty steel sliding spacers include all required mounting hardware for attaching to a tray (not included) and enable trays to slide on to the armrests from the front. The fixed braket, model 31897A, may be used with full-size and armrest-style trays and the flip-away bracket, model 31901A, is designed for use with armrest-style trays. The flip-away bracket perm
The Adjustable J Hook Bracket Hardware Seating Package, package 20XX, is seating hardware designed for use on a wheelchair. The Package includes a solid back insert including T-nuts; a solid seat insert including T-nuts; a wide, 1.5-inch offset seat to back hinge; a pair of 1- inch diameter tube two-hole J hooks; a pair of five-hole adjustable L brackets; a pair of 1-inch diameter tube six-hole J hooks; a pair of two-hole adjustable L brackets; a 1-inch diameter tube drop stop; and a 1-inch diam
Adjustable-Drop Hardware Kits are seating hardware general designed to attach drop seats to wheelchairs. The kits include four J-brackets, four L-brackets, and screws and locking nuts needed to adjust the brackets and to secure the brackets to the Drop Seat (see separate entry). The hardware in the Kits can be raised and lowered to adjust the Drop Seat. DIMENSIONS: Model 32517 fits chairs with 7/8-inch tubes and model 32518 fits chairs with one-inch tubes.
Complete line of hardware for attaching seating components to wheelchairs. Includes seat and back hooks, trunk support brackets, abductor brackets, rail clamps, head and footrest brackets, power wheelchair control box brackets, and fastening hardware.
Aluminum Shells are designed for mounting on cushions in seating systems. Sizes range from 12 to 18 inches in width, 10 to 22 inches in length. Each shell has pre-punched holes for attaching interfacing hardware and accessories. They will fit Contour-U, Sunmate, Jay, T-foam, Roho, or custom cushions. The shells will support body weight up to 250 pounds.
The Armrest Fixed Bracket, model 31897, is an add-on armrest bracket designed to allow any tray to be attached to wheelchairs. The 1/8-inch steel bracket has a baked epoxy finish. INSTALLATION: The bracket is attached to the underside of the tray using the included hardware; the tray is then installed on a wheelchair by sliding the bracket over any standard or padded armrest. WARRANTY: The manufacturer warrants this product against defects in workmanship and materials for 90 days from the date o
The Armrest Flip-Away Bracket, Model 31901, is a bracket designed to connect trays to wheelchairs and allow the trays to be flipped up 90 degrees. The bracket is 1/8-inch steel with a baked epoxy finish and includes an aluminum flip bar and spacers. INSTALLATION: The bracket is attached to the bottom of the tray with the included hardware; the bracket slides over any standard or padded armrest. WARRANTY: The manufacturer warrants this product against defects in workmanship and materials for 90 d
The Attaching Hardware Kit, model 31096H, is lapboard mounting hardware designed to attach lapboards and trays to wheelchairs. This kit includes four truss head phillips screws, four mushroom head T-nuts, and four plain T-nuts and provides sufficient hardware to attach two clamps or brackets to a tray (tray not included).
The Attaching Hardware Kit, model 33066, is lapboard mounting hardware designed to attach lapboards and trays to wheelchairs. This kit includes four 10-24 x 3/8 inch flat socket head screws, four 10-24 x 0.5 inch flat socket head screws, and four plain T-nuts and provides sufficient hardware to attach two clamps or brackets to a tray (tray not included). COLOR: The screws are black.
The Ball Ratchet Set is a seating hardware allowing angle adjustment in 5 degree increments. It is made of cast and heat treated alloy steel. It can be bolted or welded inside 7/8 inch diameter by 18 gauge round tubing. The Set is useful for legrests, seat to back attachments, and other seating applications. It is available in chromed or unchromed.
The Bi-Angular Back Brackets are stainless steel brackets designed for attaching two solid back sections at 160- (model BB-6060), 165- (model BB-6065), 170- (model BB-6070), or 175- (model BB-6075) degree angles.
The BTS/STS Custom Fixtures and Bending Tool are a ball and rod fixture for STS lateral trunk support or slim line fixture for BTS lateral trunk support. They have an 18 inch rod which can be custom bent and cut. The bending tool may be clamped in a vice and used to shape the rods.
---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a custom adapted chair base plate for a child with multiple disabilities. The child is unable to sit on a chair without support and when she is at school,. she is either in her wheelchair or in a wood chair with a lap strap. Although the lap strap holds the child securely, the child can still rock her chair back and forth with a significant risk of toppling over. The child’s occupational therapist recommended that a base plate be fitted to
These Clamps are seating hardware designed to be used in wheelchair seating systems. The Positioning Clamp has applications where clamping of the mounting hardware is fastened to the tubing of the wheelchair. It is most often used on the rear of the wheel base to position the chair initially and to keep the chair from shifting. The Swivel Clamp is a riveted one-piece design, used for securing the seat to the wheel base or wheelchair. By turning the swivel hold-down 90 degrees, complete seating d
The Deluxe Reversible Extenda Arm, Model 31094, is lapboard mounting hardware designed for use with wheelchairs. The tubulat steel telescoping arm mounts under the armrest on standard padded or desk-length wheelchair arms to provide up to 8.5 inches of additional support for trays in front of the armrest. The device can also br retracted under the armrest overhang. This deluxe heavy duty version is reversible for use on the right or left side. WARRANTY: The manufacturer warrants this product to
The Direct Mount Clamp, model 247-DM100, is lapboard mounting hardware designed specifically for attaching the MYDESC desktop lapboards (see separate entries) to wheelchairs without armrests or without removable armrests. This metal clamp block has a tightening knob for use with tube framing from 0.75 to 1.25 inches in diameter. The device can be mounted either vertically or horizontally, and also features an 0.83-inch cylinder slot to mount the lapboard, or umbrellas, directly onto the wheelcha
The Drop Base is a ABS plastic solid seat panel with cutouts for wheelchair cross braces designed to allow the mounting of custom or commercial seat cushions level with or below seat rail level. The panel fits between the seat rails, with 1- and 2-inch drop hooks to fit 7/8-inch or 1-inch rails. DIMENSIONS: Sized to fit 16 and 18 inch widths.
The Drop Brackets and Hooks are stainless steel drop hooks designed for mounting seats and backs into tubular frame bases. The "L" brackets allow angle adjustment with 1, 3, 5, or 7 holes. DIMENSIONS: 1-, 2-, and 3-inch deep Drop Hooks are available available for 7/8 or 1 inch diameter tubing, with spacers for 1/2 inch increments.
The Drop Seat Base ($42.50) and Hardware ($169) are a combination solid seat insert and adjustable hook hardware designed to fit 7/8 or 1 inch diameter wheelchair seat rails. Gravity hook assemblies allow automatic locking of the seat base onto the frame. It requires cutting of the plate to accommodate wheelchair cross-frame tubes, and drilling to mount hardware in appropriate locations.
Drop Seats are solid seat inserts are designed for use by individuals who use wheelchairs. Made of seven-ply birch, these seats have pre-drilled mounting holes and include T-nuts. Cutout slots fit around chair frame crossmembers. DIMENSIONS: Model 31649 fits chairs with 14-inch seats and is 14 x 11 inches; model 31651 fits chairs with 16-inch seats and is 15 x 13 inches; model 31655 fits chairs with 18-inch seats and is 17 x 15 inches; and model 31656 fits chairs with 20-inch seats and is 19 x 1
The E-Z-Lock Tray Clamp, Model 31096, is lapboard mounting hardware designed to secure lapboards and trays to wheelchairs. This clamp is designed to attach any tray to any wheelchair arm using a simple locking motion. OPTION: An attaching hardware kit for securing the clamp to the tray is available separately ($10.50). WARRANTY: the manufacturer warrants this product against defects in workmanship and materials for 90 days from the date of purchase.
The Figure-8 Clamp is a seating hardware and a mounting clamp for accessories designed for use with wheelchairs. The two-part clamp is used to attach controls, accessories, and other devices to wheelchairs. One side of the clamp accommodates .75-inch tubing and the other side accommodates 7/8 inch tubing. Deep-set cap screws are used to tighten clamp around tubing. Set screws can provide additional mounting stability. COLOR: Model 32310B comes in black. WARRANTY: The manufacturer warrants this p
The Fixed and Swing-Away Drop Locks are stainless steel hardware designed for stabilizing seats and backs mounted on tubular frames with drop hooks (see separate entry). The locks will fit 7/8 and 1 inch diameter tubing. Three styles are available: the Drop Stop with no tab, Swing-away Drop Lock with pivoting tab, and Drop Lock tab with fixed tab.
Fixed-Drop Hardware Kits are seating hardware general designed to attach drop seats to wheelchairs. The kits include four drop hooks, eight washers, and eight socket head screws. DIMENSIONS: Models 32617 and 32603 create a one-inch drop. Models 32618H and 32604H create a two-inch drop. Models 32542H and 32543H create a three-inch drop. Models 32617H, 32618H, and 32542H fit chairs with 7/8-inch tubes. The other models fit chairs with one-inch tubes.
The Flip Down Kit With Abductor Pad is seating hardware general and an abductor pad designed to aid in positioning individuals who use wheelchairs. This kit includes an abductor pad, one four-inch coated steel tapered L-bracket, one 2.75-inch coated steel slotted L-bracket, one 2.75-inch coated steel extrender, one anodized aluminum hinge with push-button release, and mounting hardware. The Abductor Pad is made of textured urethane self-skinning foam and come with 10-32 T-nuts embedded in all m
Abductor pad available in 2 sizes: 3 1/2 inches wide by 3 inches high by 5 inches deep, and 2 inches wide by 3 inches high by 3 1/2 inches deep. Mounts to underside of solid seat with flipdown or slide-out hardware to allow transfers.
Growth Links (Model GL01 thru GL06) and Dial Links (GL10) are hardware designed for attaching seats and backs. They are designed to be used with aluminum pans, but Wood Adaptors (Model GL21, $40/pair) are available for mounting to wooden panels. The links come in pairs and have adjustable angles. Growth links are to be used when back is supported by separate frame. Dial links support back independently.
The Headrest Hardware, series 100, is seating hardware designed for use on wheelchairs. Each hardware kit includes link hardware and offers a wide range of adjustment. This hardware offers five points of adjustability. COLOR: All hardware is black chromed and anodized.
The Interface Hardware, models 442F2 and 442F1, is seating hardware designed to allow mounting of Otto Bock seating systems into Maclaren or Pogon strollers or wheelchairs ranging from 10 to 18 inches wide. A spring-loaded plunger mechanism allows quick removal of the seat for transfer into another base or for transporting. Custom interfaces are available to accommodate mounting systems on most power bases and scooters.
The Invacare Comfort-Mate Extra Cushion and Base is a foam seat cushion designed for use with wheelchairs. This contoured, lower-profile cushion has two layers of high-density molded foam for stability and pelvic support. Beveled sides enable the cushion to be used with a drop base. This cushion has a waterproof coating and comes with a waterproof cover with a non-slip bottom. OPTIONS: This cushion can be ordered with a built-in drop base which allows lower seat-to-floor heights to facilitate fo
The Invacare Infinity Drop Base is a drop base for a wheelchair cushion designed for use by individuals who propell a wheelchair by foot or who require a lower seating position. This height-, angle-, and width-adjustable base enables the cushion to be dropped lower within the wheelchair frame than the standard seat. Quick-release hardware permits portability and provides secure attachment to most wheelchairs.
The Lateral Extension Bracket is torso support hardware designed for individuals with neurological or severe physical disabilities or cerebral palsy. The bracket expands the range in which seating supports can be adjusted laterally. The unit is attached at the end of the adjustment slot of the existing trunk lateral brackets and provides almost 3 extra inches of width adjustment for growing children and other individuals who need extra expansion of their seating system. This bracket bolts to mo
The Lateral Thoracic Pad Assembly, model ASTP, is a lateral trunk support designed to provide support to the sides of the upper body area. Stainless steel slide brackets (included) are used for mounting the pads to a solid back panel. A knob on the bracket permits easy removal. The pads are cold rolled steel, bent to 5 inch radius, with captive fasteners. These can be ordered unpadded or with 1/4-inch closed-cell foam upholstered with neoprene rubber bonded to a nylon terry cloth slip cover. SIZ
Heavy duty adjustable hardware system for positioning devices in close proximity to user. Ball joints allow angulation but tighten securely to maintain position. Includes table mount bracket, quick tightening handle, terminating plate for keyboard evaluation.
The Miller's Complete Support Systems are lateral trunk support components designed to be mounted off the seat, back insert, modular pan, or wheelchair frame, depending on the application, to give support to the trunk and pelvic areas or to provide adduction. Components of the seat, back, or pan-mounted systems include fixed, swing-away, and multiplane inserts, pads, and doglegs. The doglegs allow approximately 2 additional inches of lateral adjustment. The Multi Plane provides greater flexibili
The Miller's Mounting Hardware Components are designed for affixing wheelchair accessories to solid seat and back panels or to 7/8 and 1 inch wheelchair frame tubing. Fixed, swingaway, and adjustable type clamps and brackets are available. COLOR: Silver or black chrome finish.
The Moss Lap Tray is a molded plastic lapboard designed to mount to Otto Bock MOSS II seating system armrests (see separate entry) with the U-shaped aluminum frame. Fits 9.5, 11.5, 13.5, 16, and 18 inch seating systems.
-- PROTOTYPE --------- PURPOSE: To create a prototype of a wheelchair seat that aids wheelchair users to change his or her seated position periodically. Changing position when seated for a long period of time is especially important for wheelchair users who spend almost every making moment seated. Failure to do so can result in deformities, bedsores, or considerable pain. The Swiss research group, Empa, is working with an ergonomics company to develop a new type of wheelchair seat that periodica
Mounting Brackets and Trunion Brackets are interfacing hardware designed for mounting seating systems on a variety of mobility bases. Quick release or permanent mounts are available. The brackets ($25) are for mounting on wood or aluminum shells (see related entry) and come in two sizes: 7/8 inch and 1 inch. The trunion mounts ($58) are available in the same sizes.
The Multi-Axis Offset Headrest Assembly, model 32465, is seating hardware designed to attach offset headrests to standard wheelcahair frames. The entire assembly is designed to be used with small, large, combination, small lateral support, and neck rest style headrests (headrests sold separately). The heavy-duty assembly features an offset block that swivels on a ball for headrest adjustment in any direction, a straight bar that adjusts horizontally, a heavy-duty mounting ring, a durable mounti
The MYDESC Direct Mount Model 350-DM500, and the 90 Degree Direct Mount Model with Elbow Assembly 350-DM900, are mounting hardware for the MYDESC lapboards to clamp onto a wheelchair's frame or armrest. They include clamps and an adjustable MYDESC lapboards. The clamps will accommodate tubing from 3/4 to 1.25 inches in diameter, and both can be mounted either horizontally or vertically. Model 350-DM900 provides more height and distance from the wheelchair user's body.
The NE-AT Headrest Bracket is headrest mounting hardware designed for people with neurological or mobility disabilities, spinal cord injury, cerebral palsy and other individuals who need adjustable head support. This hinged bracket has 0.25-inch countersunk mounting holes spaced 1 inch apart, with a spring loaded crank handle for tightening in tight spaces.
The NE-AT Quick Release Mini Trap Assembly is a a wheelchair mounting bracket that can support an armrest, a drink holder, a tray, or a laptop computer mount. This small, strong quick-release bracket comes in two versions, angle adjustable or not angle adjustable, and it has optional locking pins. DIMENSIONS: 2 x 2 x 0.75 inches.
The NE-AT UseR Adjustable Lateral (NE-ATURAL) Bracket Mount is lateral trunk support hardware designed for use by individuals with neurological or severe physical disabilities or cerebral palsy. This width-adjustable lateral bracket mount interfaces with most commercial and custom seating systems and converts most commercial and custom lateral brackets into lateral brackets that can be adjusted in width by the user or caregivers to make room for winter jackets or sweaters. Existing swing away o
The NE-AT YA (Yet Another)Tray Mounting Bracket is lapboard mounting hardware designed for use with wheelchairs. The YA Bracket converts most commercial trays (Pin Dot, XL, Avanti, Invacare, etc.) from the existing slide-on or clamp style armrest mounting to a four bar linkage type clamp. This type of mounting can extend the life of the existing armrest pads, provide a stronger hold, and accommodate different size wheelchairs.
The NEasy Aug Com Swing Away Mounting System is a wheelchair mounting kit for communicators or lapboard mounting hardware designed fo use by individuals who use wheelchairs. This compact, heavy-duty modular mounting system for small to large devices or trays can be released and swung away by the user with only one or two pounds of pressure. Each swing away joint automatically locks into position with a stainless steel, spring-loaded pin at 0 degrees, 90 degrees (optional), and 180 degrees (optio
The OBUS Seat is a seat panel designed to relieve fatigue from the buttocks to the sacrum and to the lumbar and thoracic areas. The panel will support up to 75 percent of the body's weight and prevent the ischial tuberosities to sink into soft cushions. The coccyx is protected by a contoured buttocks frame with a cut-out seat depression. The device also protects the thighs with additional molded padding to reduce fatigue, improve circulation, help prevent swollen ankles and feet, and maintain pr
The Otto Bock Tall Back and Modular Back Headrest Mounting Kit ($5) and the Otto Bock Headrest Adapter Kit ($20) are headrest accessories that allow attachment of Otto Bock headrest mounting hardware directly to the Jay Back cushion, compensating for the contour of the cushion.
Positioning Hardware is seating hardware general designed for attaching positioning aids to wheelchairs. Available items include two-, four-, six-, and eight-hole adjustment hooks; drop hooks; drop hooks for thigh pad inner mount; drop hooks for thigh pad outer mount; side, bottom, and parallel flanges; latch tabs; universal rear bracket; and a swing tab U-bracket. Also available is a seatlock; a seatblock; a headrest mounting plate; a child's headrest support; an adult headrest support; and six
The Quad Care Attaching System, Model 31878, is lapboard mounting hardware for use by people who are quadriplegics or who have upper extremity disabilities. The kit allows the user to attach a tray or lapboard to wheelchair armrests by using clear vinyl thumb loops to streetch elastic bands over baked epoxy metal attaching pegs. The elastic loop stretches around the armrest and the pull-ring hooks onto metal bracket. The kit includes elastic loops, vinyl pull-rings, and metal brackets with atta
Mounting clamps for removing solid wheelchair seat and back. Attach to wheelchair frame. Keeps wheelchair seat and back securely in place. Twist the lock and both seat and back slide out to fold the wheelchair. Black finish. Available in 3/4 inch, 7/8 inch or 1 inch sizes. .
The Quick Release Hardware Kits are silver or black chrome plated hardware sets for mounting seat or back accessories to 7/8- or 1-inch tubing wheelchair frames. The kits include frame clamps with lugs, quick release brackets with spring-loaded knobs, and T-nuts and bolts for mounting to solid seat or back panels. Components may also be ordered separately.
Molded ABS plastic base with front pommel to encourage leg abduction, 7 degree slope from front for anti-thrust effect, 13 degree side to side slopes to center hips, to be placed under any Roho Dry Floatation Cushion. Weighs approximately 1 pound. Available in 3 standard sizes: 15 inches by 15 inches, 16 inches by 16 inches, 16 inches by 18 inches. Custom sizes available. 18 month warranty.
The Saddle Complete Seat is a drop seat base with a foam or gel and foam seat cushion designed for use in wheelchairs. The unit comprises a SmartSeat drop seat and a Saddle Cushion. The adjustable platform allows the wheelchair seat to be lowered and the angle adjusted to enable the user to propel the chair using his/her feet. The high-strength molded platform attaches to the chair with steel hooks and stabilizer straps that connect under the chair secure the platform.The cushion also features a
Safe•T Mate Drop Seat with Integrated Alarm, model SM-007, is a wheelchair drop seat base and wandering patient system designed for use by wheelchair users with Alzheimers disease or cognitive disabilities. This system combines a solid drop-seat with a rugged, detachable 95- decibel alarm with automatic reset. DIMENSIONS: The drop seat is 3/8-inch thick and fits chairs from 16 to 22 inches wide. WARRANTY: Limited lifetime guarantee.
Complete line of seating hardware for mounting backs, seats, lateral trunk supports, abductors, headrests, leg and footrests in wheelchairs and other mobility bases. Adjustable and non-adjustable, knob-release and drop hook styles. May be ordered in complete kits or by individual components. Optional components $93.00 to $2.00.
The Adjustable Seat Hooks are designed to serve a variety of extended wheelchair seat positioning applications, such as angling or height adjustment. These stainless steel hooks are countersunk for a ##10 flathead screw. DIMENSIONS: The hooks are 0.75-inch wide and are available to fit tubes 0.75 inch, 7/8 inch, 1 inch, or 1 3/16 inch in diameter. COLOR: Available in black or stainless steel
The Seat Hook, Drop is one-piece seating hardware designed for lowering and leveling a wheelchair seat. It is made of stainless steel and fabricated with two 17/64 inch x 5/8 inch mating slots. Both ends are curved and deburred for a smooth finish. DIMENSIONS: The hook ends fit tubes 0.75 inch, 7/8 inch, 1 inch or 1 3/16 inches in diameter. The drop offsets range from 1 inch to 6 inches in 1-inch increments. COLOR: Available in black or stainless steel.
The Seat Hook, Lift is seating hardware designed to lift and level wheelchair seats. It is made of stainless steel and fabricated with two 17/64 inch x 5/8 inch mating slots. Both ends are rounded and deburred for a smooth finish. DIMENSIONS: The hook fits tubing 0.75 inch, 7/8 inch, 1 inch or 1 3/16 inches in diameter. The lift offset ranges from 0 inches, 0.5 inch, or 1 inch to 2 inches. COLOR: Available in black or stainless steel.
The Seat-to-Back Brackets are stainless steel brackets designed for rigidly attaching a solid seat and back to each other at 80-degree (model BS-6080), 85-degree (model BS-6085), 90-degree (model BS-6090), 95-degree (model BS-6095), or 100-degree (model BS-6000) angles.
Seating Hardware are components for seating systems that include: 7 types of head and neck supports, 5 models of outer pommel supports, 2 inner pommel support, anterior stop bars, 10 footrest bracket options, 25 suspension hook options, slide brackets, strap hooks, tray brackets, 2 types of headrest hardware, single end button locks, removable lateral hardware, laterals, box seat hardware, solid seat and back brackets, solid seat and back hinges, kids seat bracket, and a drop away pommel.
Seating Hardware is designed for use with wheelchairs. This hardware is made of steel and includes 90-degree brackets and J-hooks (sold separately). DIMENSIONS: All hardware has 0.5-inch spacing, COLOR: Black.
---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a custom adapted seating support for a child with dystonic cerebral palsy. When sitting in a chair, the child pushes his pelvis forward and becomes uncomfortable, and the child concentrates more on sitting than on his books, crafts, and other activities. The family attempted to remedy the seating issue by adding a two-piece insert, the commercially available “tomato seat;" however, this device did not secure properly to the chair. The child
The Sliding Headrest Bracket is headrest mounting hardware designed for people with neurological or mobility disabilities, spinal cord injury or cerebral palsy. It is added to a headrest on a seat or wheelchair to enable headrest adjustments. This slotted interface bracket allows the headrest to be offset to either side, with infinite lateral adjustment up to 2 inches for an Otto Bock or NE-AT Headrest Bracket (see separate entry). This bracket attaches to the seating system using the existing h
The SmartSeat Drop Seat is a drop seat base designed for use in wheelchairs. This adjustable platform allows the wheelchair seat to be lowered and the angle adjusted to enable the user to propel the chair using his/her feet. The high-strength molded platform attaches to the chair with steel hooks and stabilizer straps that connect under the chair secure the platform. DIMENSIONS: Models are available for 16-, 18-, and 20-inch wheelchairs. The seat can be lowered up to three inches.
Custom size solid back with 1 inch medium density foam on 1/2 inch birch plywood. Upholstered with cover foam and vinyl cover. T-nuts for hardware attachment and headrest mounting. Custom foams available. Modifications available include curved solid back and I-back cutout. May be ordered without aluminum hardware, or mounted to chair with velcro loops, cinch straps, stationary knob-release hardware, adjustable knob-release hardware, non-adjustable drop hooks, or adjustable drop hooks. Hardware m
Solid Drop Seat Systems are solid seat inserts designed for use by individuals who use wheelchairs. The systems include a seven-ply birch solid seat insert and jeavy-duty J-brackets that may be adjusted to raise or lower the seat to achieve proper positioning for the user. The seat features cut out slots to fit around frame crossmembers. DIMENSIONS: The seat insert is 3/8-inch thick. Model 31642 fits chairs with a 16-inch seat and is 13 x 16 inches. Model 3143 fits chairs with 18-inch seats and
Custom size solid seat with 1 inch medium density foam on 1/2 inch birch plywood. Upholstered with cover foam and vinyl cover. T-nuts for hardware attachment and abductor mounting. Custom foams available. Modifications available include anti-thrust seat, leg length discrepancy, and built-in abductor. May be ordered without aluminum hardware, or mounted to chair with cinch straps, stationary knob- release hardware, adjustable angle knob-release hardware, non- adjustable drop hooks, or adjustable
The Solid Seat, model SS1000, is a drop seat for a wheelchair designed for use by individuals with a need for a lower seat due either to a high cushion or who propel the wheelchair with their feet. The Drop Seat is made of durable HDPP and fits most manual and powered wheelchairs. The hole pattern accomodates one-inch mounting increments. Velcro strips are provided to secure a cushion. The hardware adjusts from one-inch above a tube frame to 3 inches below a tube frame. DIMENSIONS (LxW): Avai
Spacer Kits are seating hardware designed to be used in wheelchair seating systems. Along with adjustable brackets, spacers are used to space out hooks. For example, a spacer is used when mounting a 14-inch seating system on a 15-inch wheelchair. Spacers are fabricated from a solid piece of aluminum with clearance holes for ##10-32 screws placed on 1/2 inch centers. A Spacer Kit contains one Spacer Block, two ##10-32 x 1 inch Flat Head Socket Drives with Grade 8 screws, and two ##10-32 Nylok Nu
The Adjustable Square Tubing Seat Hooks are designed to serve a variety of extended wheelchair seat positioning applications, such as angling or height adjustment in conjunction with an adjustable bracket. Made of stainless steel, they are countersunk for a ##10 flathead screw. DIMENSIONS: The hooks are 0.75-inch wide and are available to fit square tubes 0.75 inch, 7/8 inch, or 1 inch in diameter. COLOR: Available in black or stainless steel
The Square Tubing Seat Hook, Drop is designed to lower and level the seat in wheelchairs with three-quarter inch square tubing. It is made of stainless steel and fabricated with two 17/64 inch x 5/8 inch mating slots. Both ends are rounded and deburred for a smooth surface. DIMENSIONS: The drop offset ranges from 0 inches to 1.5 inches in half-inch increments. COLOR: The hooks are available in black and stainless steel.
The Square Tubing Seat Hook, Lift is designed for raised seat applications on wheelchairs with three-quarter inch square tubing. It is made of stainless steel and is fabricated with two 17/64 inch x 5/8 inch mating slots. The ends are both rounded and deburred for a smooth surface. DIMENSIONS: The lift offset is 1 inch. COLOR: Stainless steel or black.
The Steel Channel Bracket Attaching System, model 30300, is lapboard mounting hardware designed to secure armrest-style trays to wheelchairs. This heavy-duty steel bracket includes all required mounting hardware for attaching to a tray (not included) and enables a tray to slide on to the armrests from the front. This flip-away bracket fits standard wheelchair armpads and permits chair entry and exit without removing the tray. DIMENSIONS: Fits 1 1/8-inch high standard pads. WARRANTY: This product
The SupportPro Complete Seat is a drop seat base with a foam or gel and foam seat cushion designed for use in wheelchairs. The unit comprises a SmartSeat Drop Seat with a SupportPro Cushion. The adjustable seat platform allows the wheelchair seat to be lowered and the angle adjusted to enable the user to propel the chair using his/her feet. The high-strength molded platform attaches to the chair with steel hooks and stabilizer straps that connect under the chair secure the platform. A SupportPro
The Top Drop Clamp Attaching System, model 31070, is lapboard mounting hardware designed to secure trays to wheelchairs. This system enables the tray (not included) to be positioned straignt down on the armrests and requires only 3/8-inch clearance under the armpad which enables the tray to be used when a joystick or other control is mounted next to the armpad. The tray locks on with the turn of a handle. Made of glass-filled nylon, the clamps adjust to fit arms of different widths and pads of d
The Tray Bracket ($50, model TR30 & TR31 for left and right armrests, respectively) and the Tray Bracket Receptacle ($70, TR32) are designed to attach a tray to the armrest of a wheelchair or seating system. The units are compatible with many armrests. The bracket is mounted on one armrest and the receptacle is mounted on one side of tray. Support on both sides is recommended for heavy duty applications.
Tray Clamps, Model 31086, are lapboard mounting hardware designed to mount trays and lapboards to wheelchairs. These clamps provide a means of locking trays to wheelchair frames using one lever motion. WARRANTY: The manufacturer warrants this product to be free of defects in materials and workmanship for 90 days from the date of purchase.
The Tray Stay Clamping System is lapboard mounting hardware designed to attach trays and lapboards to wheelchairs. The modular clamping system allows the user to adjust the height and position of the tray by attaching the base channel system to the tray and inserting the appropriate spacers. The clamps are secured by an attachment knob. The system can be used to mount trays directly to the wheelchair armrest and crossbar, the armrest pad, or to the manufacturer's Extenda-Arms, which provides ad
The Tray and Hardware are a lapboard and mounting hardware designed for wheelchairs. The polycarbonate tray may be ordered with or without flip locks. Requires cutting out for trunk, sanding edges, and mounting of flip locks. OPTIONS: Tray elbow protection pads also available as individual or full pad. Mounting hardware may be ordered separately. DIMENSIONS: 18 x 24 inches (Small) and 24 x 27 inches (Large).
The Tube Arm Bracket Attaching System is lapboard mounting hardware designed to secure trays to wheelchairs. These brackets enable a tray (not included) to slide on to tube-style armrests from the front. The brackets are attaached at both ends of the tube, enabling the tray to be attached to the top of the armrests (mounting hardware is not included). hook-and-loop straps (not included) may be used with these brackets for extra stability. OPTIONS: Mounting hardware (no. 31096H).SIZES: Small (no.
The Universal Arm Mount, model 347-UA503, is a mounting clamp for wheelchair accessories designed specifically for attachment of the MYDESC EZ-Removable Arm (see separate entry). This metal clamp block can be used with wheelchair tubing from 0.75 to 1.25 inches in diameter, and provides a 0.78 inch cylinder slot for mounting the EZ-Removable Arm directly to the wheelchair frame. The clamp may be mounted either horizontally or vertically.
The Universal Bracket System is a set of brackets designed for mouting trays and lapboards on wheelchairs. These lightweight brackets are height- and width-adjustable to fit any wheelchair with standard arms. The rust- and corrosion-resistant brackets are removable for transfers and emergencies and they feature safety stops to prevent the tray from being pushed into the user.
The Universal Headrest Mounting Plate is seating hardware designed for use with wheelchair headrests. This plate enables a variety of headrests from various manufacturers to be interchanged as needed. The headrests may be changed without having to redo the T-nuts in the back.
The Varilite Drop Base System is a wheelchair cushion drop base designed for use by individuals with lower extremity disabilities, mobility disabilities, and spinal cord injury. This system lowers the wheelchair seat base for individuals who need to be lower to the ground to self-propel or who have difficulty transferring to a higher surface. The system includes a base constructed from durable PVC plastic and L-J brackets made of hardened steel. The brackets allow up to four inches of height ad
Wheelchair Adaptive Hardware is seating hardware designed for attaching seating components to standard wheelcahir frames. Available hardware includes drop hooks, adjustable angle hooks, horseshoe clips, U-brackets, seat blocks and locks, strap hinges, adjustable headrest support brackets, and lateral trunk support brackets and pads. WARRANTY: The manufacturer warrants these products against defects in materials and workmanship for 90 days from the date of purchase.
The Wheelchair Snack Tray, model 70621-0000, is a lapboard designed to clamp to wheelchair tubing to hold snacks and beverages. The tray sticks to a platform by Velcro pads to facilitate removal for cleaning. The try is made of polystyrene; metal parts are epoxy coated. DIMENSIONS: 6.5 x 9.75 inches.
Three-piece headrest with center pad and two adjustable side pads. Standard pad sizes: center 4 inches wide by 6 inches high, side pads 4 inches wide by 2 inches high. Custom sizes available. Center pad has occipital shelf or can be ordered flat. Mounting hardware allows adjustment of side pad depth, angle, and width, and adjustment of entire headrest in height, forward/back, and angle. Attaches to solid back.
Pads are foam padded plywood, covered with naugahyde. Full side pads are 4 inches by 9 inches or 4 inches by 11 inches. Deep curved pads in 3 sizes: 3 inches by 5 inches, 4 inches by 6 inches, 6 inches by 10 inches. Mount to solid backs with angle brackets, or to seats with offset brackets or mounting rail brackets. Custom foam and pad sizes available. Full side pads available in 12 colors, curved pads in black only.
Pads are foam padded plywood, covered with naugahyde. Oval shaped pads in 3 sizes: 4 inches by 5 inches, 4 inches by 6 inches, and 5 inches by 7 inches. Rectangular pads are 4 inches by 6 inches. Deep curved pads in 3 sizes: 3 inches by 4 inches, 4 inches by 4 inches, 6 inches by 6 inches. Mount to solid backs with offset brackets, angle brackets, or mounting rails. Fixed or removeable. Custom foam and pad sizes available. Oval and rectangular pads available in 12 colors, curved pads in black on